Mash and sparge water calculator for all-grain brewing

Enter your total grain weight, your batch size and a few details about your kettle, and see how much water to mash in with, how much to sparge with, and how full the kettle will get. It remembers your kettle’s details for next time.

The calculator

All the malts in the recipe, added together.

How much wort you want in the fermenter after the boil.

Usually 60 minutes: check your recipe.

Your kettle

Measure these once: they’re remembered for next time.

How much boils away in an hour: about 2 litres on a 1600W element. To measure yours, see the questions below.

Wort you can’t get out after the boil: hops, sediment and what sits below the tap.

About 0.8 litres a kilo if you squeeze the bag, 1 if you let it drain.

Its MAX or FULL line (27 litres on our Klarstein Füllhorn): you’ll be warned before you go past it.

Your water

Mash water
–L
Sparge water
–L
Total water
–L
Wort before the boil
–L

–LMash water–LSparge waterCheck your readingsAll results

How it works

Start from the fermenter and work back. The wort before the boil has to cover the batch, what’s left in the kettle (hops, sediment, the space under the tap) and what boils away. The grain keeps some water too, about 0.8 litres a kilo when it’s drained or squeezed in a bag, so that’s added on top.

The mash water is 2.7 litres per kilo of grain plus 3.5 litres, the formula The Homebrew Shop’s kits use. The rest is the sparge, rinsed through the grain after the mash.

The calculator warns when the mash, water plus the grain itself (about 0.67 litres a kilo), or the wort before the boil, would go past your kettle’s maximum fill line.

From our brews

Pilot Episode had 5.6kg of grain for 21 litres. Our Klarstein Füllhorn boils on its 1600W element, so about 2 litres an hour boil off (it can’t manage much more than 2.5 even in theory), and about 2 litres stay behind in the kettle. That’s 18.6 litres to mash in and 10.9 to sparge, 29.5 litres in all. On the day I mashed with 23 and used only 5 to sparge, and noted it should have been nearer 10.

Questions

How do I measure my kettle’s boil-off rate?
Fill it with a known amount of water, boil it as hard as you would on brew day for 30 minutes with the lid off, let it cool a little and measure what’s left. Double the loss for litres an hour.
Why do I end up short of my batch size?
Usually because the grain kept more than expected, or the boil was harder. Measure your real losses on a brew day and put them in: the calculator remembers them.
Does this work for brew in a bag?
Yes. With a bag you can mash with all the water at once: use the total water, and set “Water the grain soaks up” to about 0.8 litres a kilo if you squeeze the bag, or 1 if you just let it drain.
What’s the difference between mash water and sparge water?
Mash water soaks the crushed grain at mash temperature, so its enzymes can turn the starch into sugar. Sparge water rinses the sugar still clinging to the grain once the mash is done, so it ends up in your wort rather than in the spent grain.
What temperature should sparge water be?
About 75 to 78°C. Hot enough to rinse the sugar out easily, but not so hot that it draws harsh tannins out of the grain husks.
What if I’m short of wort before the boil?
Sparge with a little more water, or top up the fermenter with clean, cooled water after the boil. Topping up lowers the original gravity slightly, so take your reading once it’s mixed in.

More tools

Fisher & Forbes Brewing Co, home