IBU calculator for homebrew hop bitterness
Enter the hops you’re boiling, the alpha acid printed on each packet and how long each one boils, and see roughly how bitter the beer will be, and whether it’ll taste balanced, malty or bitter.
How it works
Bitterness comes from the alpha acids in hops. They only turn bitter when they’re boiled, and the longer they boil, the more of them change, up to about an hour. That’s why hops added at the start of the boil are for bitterness, and hops added near the end, or after it, are mostly for flavour and aroma.
The calculator uses Tinseth’s formula, the one most brewing software uses. Each hop’s weight and alpha acid give how much alpha acid goes in; its boil time and the wort’s gravity give how much of that turns bitter (stronger wort holds on to less). The answer is in IBU, International Bitterness Units: roughly milligrams of bitter compounds in a litre of beer.
Balance compares the bitterness with the malt’s sweetness: the IBU divided by the gravity points (the 50 in 1.050). About 0.5 tastes balanced, nearer 1 tastes properly bitter, like an IPA, and below 0.3 tastes sweet or malty.
It’s an estimate: hops vary, and so does every kettle. Use it to compare recipes and plan changes rather than as a measurement.
From our brews
Pilot Episode’s kit had two bags of boiling hops: 20g for 60 minutes and 20g for 30. The bags didn’t say their alpha acid, so we can’t give its true bitterness. If they were around 10%, typical of American IPA hops, that’s about 38 IBU in our 21 litres at 1.052: a balance of about 0.7, properly hoppy. It’s also why that brew log shows no IBU: we only show figures we can work out from what we know.
Questions
- Where do I find the alpha acid?
- It’s printed on the hop packet as a percentage, often marked “AA” or “alpha”. It changes from harvest to harvest, so use the figure on your packet rather than a typical one.
- What about dry hops and hops added at the end?
- Leave dry hops out: they add aroma and flavour, not bitterness. Hops added at flameout or in a whirlpool add a little bitterness while the wort is still hot, but the formula can’t count it well; put them in at 0 minutes and they count as none.
- How bitter should my beer be?
- As a rough guide: wheat beers 10 to 15 IBU, lagers 15 to 25, best bitters 25 to 40, pale ales 30 to 50 and IPAs 40 to 70. Double IPAs and imperial stouts can go higher still.
- Can I use it for a beer kit?
- Only if the kit lists its hops’ weights and alpha acids. Most extract kits come as hopped malt extract, with the bitterness already in it, so there’s nothing to work out; the kit’s description often gives its IBU.
More tools
ABV calculator
Work out a homebrew’s ABV, attenuation and calories from hydrometer readings, including fruit or sugar added during fermentation.
Open the ABV calculatorHydrometer correction
Correct a hydrometer reading taken from warm or cold wort or beer to its true gravity, for the temperature your hydrometer is calibrated to.
Open the hydrometer correctionCarbonation calculator
How much priming sugar, or how many carbonation drops, to put in each bottle for the fizz you want: for 330ml, 500ml and 750ml bottles.
Open the carbonation calculatorBottle calculator
How many bottles a homebrew batch will fill, in 330ml, 500ml, 750ml or any size, after the sediment, with spares to sanitise in case.
Open the bottle calculatorWater calculator
Mash and sparge water for an all-grain brew day, from your grain bill, batch size and kettle’s boil-off, with a warning before the kettle overflows.
Open the water calculatorRecipe scaler
Scale a homebrew recipe or kit to the batch size you want: grain, hops, sugar and fruit, from a big kit down to a demijohn or up to a bigger brew.
Open the recipe scalerDilution calculator
How much water to add to bring your wort or beer down to a gravity, or what the gravity will be once you top it up with water.
Open the dilution calculator