---
title: "Bottle calculator: how many bottles a batch will fill"
description: "How many bottles a homebrew batch will fill, in 330ml, 500ml, 750ml or any size, after the sediment, with spares to sanitise in case."
url: https://www.fisherforbesbrewing.com/tools/bottle-calculator/
publisher: Fisher & Forbes Brewing Co (https://www.fisherforbesbrewing.com)
---

# Bottle calculator: how many bottles a batch will fill

Enter your batch size and bottle size, and see how many bottles you’ll fill and how many to sanitise, with a few spare, so you’re never hunting for a clean bottle with the bottling wand dripping in your hand.

The calculator itself works on the page: Bottle calculator.

## How it works

Not all of the batch makes it into bottles. The yeast sediment at the bottom of the fermenter stays behind, along with a little in the tubing and the bottling bucket, so the calculator takes that off first. About a litre is typical for a 20 to 23 litre batch; a dry hopped beer or one with fruit in it leaves more.

What’s left, divided by the size of a bottle, is how many it fills. If the last bottle would only be part full, it’s counted as one more, so you have somewhere to put it.

Spares are a share of the bottles you’ll fill, rounded up: 10% gives seven spares for 63 bottles. Sanitise them with the rest. A bottle with a chip in its neck, a cap that won’t crimp or a swing-top seal that’s perished is far easier to swap for a clean one than to sort out mid-flow, and it’s better to tip a few unused ones out afterwards than to run short. Have as many caps or corks ready as bottles.

A bottle size can be given in millilitres, centilitres, litres, fluid ounces or pints: choose “Another size” and its unit. UK and US fluid ounces and pints aren’t the same, so pick the right one: a UK pint is 568ml, a US pint 473ml.

## From our brews

I Am Your Guava was 21 litres in the fermenter and filled sixty-two 330ml bottles: 20.5 litres, so about half a litre stayed behind. Entered with half a litre left behind, the calculator says 62 full bottles and a 63rd with a little in it; with 10% spare, that’s 70 to sanitise.

Pilot Episode filled 42 bottles of 500ml, and Sauvignon Plonk six 750ml wine bottles from a 4.5 litre batch.

## Questions

### How many bottles do I need for a 23 litre kit?

Allowing a litre for the sediment, about 67 bottles of 330ml, 44 of 500ml or 30 of 750ml, plus a few spare. A “40 pint” kit makes about 23 litres, so it’s the same.

### How much beer is lost to sediment?

Usually half a litre to a litre and a half in a 20 to 23 litre batch: the yeast cake, plus what the tubing and bottling bucket hold back. Dry hopping or fruit in the fermenter can double it. Note how many bottles each batch actually fills, and you’ll soon know your own figure.

### How many spare bottles should I sanitise?

About 10%: half a dozen or so for a full-size batch. Enough to swap out a chipped bottle or a cap that won’t seal, and to catch the last of the beer if the batch comes out a little bigger than you expected.

### What do I do with the last, part-filled bottle?

Use a smaller bottle if you have one, especially if you prime each bottle with carbonation drops: a half-full bottle gets as much sugar as a full one, so it ends up much fizzier. If you prime the whole batch, a part-filled bottle is fine; just drink it first.

### Can I mix bottle sizes?

Yes. Decide how many of the bigger bottles you want to fill, take off what they hold (12 bottles of 500ml is 6 litres) and put what’s left into the calculator with the smaller size. The carbonation calculator gives each size its own amount of sugar or drops.

---

Source: https://www.fisherforbesbrewing.com/tools/bottle-calculator/
